RCMini5 Complete ECU with bLink

Special design for the modified engine from from stock to middle level

Over ten parameters can be adjusted by smartphone*

3D fuel, 3D ignition timing, fuel in acceleration, fuel cut in deceleration, idle rpm...etc can be adjusted

Unlock rpm limited and can define rpm limited by user

Vechicle standard control strategy, include temperture, baro compansation

Stock engine with RCMini5 ECU can increase at least 10~15% power

Plug and play

Meet the IP67 standard

RCMini5 with AF1 can achieve the fuel correction by close loop

aRacer AF module is required to run auto tune feature

*Aracer fuel management products are NOT compliant with the California Environmental Protection Agency (E.P.A.) or California Air Resources Board (C.A.R.B) for use on public roads or lands.Aracer products are for closed-course competition use only.

This product is legal for closed-course competition use only; for racing vehicles (a competition vehicle not used on public highways). Intended for off-road use or race purposes; may not meet regulations of pollution controlled roads or highways. Not legal for vehicles registered and use in California. 

RC Super 2 Complete ECU

Dual-core design, calculation speed up 50%

More accuracy operation of injection and ignition timing

Weight reduce 12%, heat dissipation10%

Can be extended several professional race kits and modules

Support all NA modified of the engine

3D Injection can be adjusted

3D ignition timing can be adjusted

Unblock rpm limited, support rpm to 16500rpm

Vehicle standard control strategy, include temperature, baro....etc. compensation

Support many popular bike model, free download map and increase performance

Increase power at least 10% by the stock engine 

Plug and Play

100% stock ECU connector, no need to cut or modify the stock wire 

Meet IP67 vehicle standard

 Autotune function ( AF1 wideband AFR module is necessary)

*Aracer fuel management products are NOT compliant with the California Environmental Protection Agency (E.P.A.) or California Air Resources Board (C.A.R.B) for use on public roads or lands. Aracer products are for closed-course competition use only.

This product is legal for closed-course competition use only; for racing vehicles (a competition vehicle not used on public highways). Intended for off-road use or race purposes; may not meet regulations of pollution controlled roads or highways. Not legal for vehicles registered and use in California. 

Fuel and Injection phase adjustable

Ignition timing and dwell time adjustable

Manifold Air Pressure base for inlet air amount calculation

Released engine speed limited

Environment temp and Baro compensation available

Free MAP download for various vehicle model (Honda, Yamaha, Suzuki, Kawasaki,Kymco, SYM…)

Increase almost 10% above power after calibration (depend on engine model)

Easy plugin (remove stock ECU and install RC1 ECU without any harness modified)

Same connector as stock ECU

RC1 ECU meet IP67 specs

Support Auto-Tune with aRacer AF1 wideband sensor module

Race & ECO MAP real time switch with iMode

Launch mode for racing start

Valet mode for anti thief or running usage

Aracer fuel management products are NOT compliant with the California Environmental Protection Agency (E.P.A.) or California Air Resources Board (C.A.R.B) for use on public roads or lands.Aracer products are for closed-course competition use only.

This product is legal for closed-course competition use only; for racing vehicles (a competition vehicle not used on public highways). Intended for off-road use or race purposes; may not meet regulations of pollution controlled roads or highways. Not legal for vehicles registered and use in California. 

Multi-Function Display DG-1

It can be shown wideband AFR, battery voltage and timer function with AF1

Extendable sensor modules in the feature: exhaust pipe temp. coolant temp. boot pressure...etc

OLED all day viewable display and scratch proof panel design

3 color LED highlight, alarm condition setting

It is suitable for all motorcycle models

1 to 2

extend Cable

It is be used to extend one ecu port to 2

, so ecu can be linked with sensor modules, iMode Gen II... etc.